Slide Mounting Media
Electron Microscopy Sciences Technovit H7100 – GMA kit
Technovit H7100 – GMA kit consists of: 500 ml Glycol Methacrylate monomer, 5 x 0.6g packs Hardener I, 40 ml Hardener II; Technovit Glycol Methacrylate embedding kits developed by Kulzer in Germany are the most convenient to use and offers the best embedding results. Kits give better results offering improved morphology and allows for 1 micron serial sectioning. olymerization temperature never exceeds 40 degree C, which makes either kit a potential choice for enzyme histochemistry. Technical Note: GMA resin-based products (Technovit 7100, 8100) should not be used when epoxy removal from specimens is required. There is no known method of GMA epoxy removal (including methoxide) that does not effectively render specimens unusable. Instead, MMA resin-based products such as Technovit 9100 should be selected.
Electron Microscopy Sciences EMS Colloidal Graphite, Alcohol Base 30 GR
Isopropal base collodal graphite has a Flat surface texture. The average flake size is 1 micron. Service temperature is 204 degree C.
Electron Microscopy Sciences Low viscosity embedding media kit, 1 kit
Provides excellent penetration for embedding biological tissues and rapid infiltration. Easy to prepare. The hardness is adjusted by changing the proportion of the flexibilizer (DER 736). The blocks have good trimming and sectioning qualities. Thin sections are tough under the electron beam. Kit consists of: 450 ml NSA, 225 ml ERL 4221 , 225 ml DER 736 , 25 ml DMAE.
Electron Microscopy Sciences Colloidal Silver Liquid, 15 g
1-Methoxy-2-propanol base. Fast drying. Average grain size less than 1 µm and Silver content is 60%. Sheet resistance is 0.02 ohm per square inch at 1 mil thickness. Comes with a brush attached to the cap. Service temperature is 30 minutes at 200°C.
Electron Microscopy Sciences Technovit 8100 Embedding Kit
Technovit Glycol Methacrylate embedding kits developed by Kulzer in Germany are the most convenient to use and offers the best embedding results. Kits give better results offering improved morphology and allows for 1 micron serial sectioning. Polymerization temperature never exceeds 40 degree C, which makes either kit a potential choice for enzyme histochemistry.
The initiator is prepackaged, eliminating messy handling of dry components, and by eliminating aromatic amines from the formation, the components are significantly less toxic. The consistent high quality of raw materials used to make the resin allows for a permanent clear colorless block and, most important, reproducible results
Electron Microscopy Sciences LR White resin only; Hard Grade Catalyzed
A very low viscosity (8cps), non-toxic resin, suitable for both Light and Electron Microscopy. LR White is a polar monomer polyhydroxylated acromatic acrylic resin. It can be cured by heat or by UV light. Sections of polymerized LR White resin are hydrophilic. This character allows immuno-cytochemistry reagents to easily penetrate into the sections and etching of the sections is not necessary (etching sections will effect delicate tissue antigens). LR White sections also show minimal non-specific staining. Its low viscosity makes it ideal for infiltrating decalcified bone and teeth as well as plant tissues. It is available in medium and hard grade.
Electron Microscopy Sciences EMbed 812, 450ml
EMbed 812 has the same characteristics as Epon 812, physically, and provides the same results in preservation, handling, curing and sectioning. EMbed 812 may cause etching on selected plastics. All formulas for mixing and using Epon 812 can be applied to EMbed 812
Electron Microscopy Sciences Technovit 3040 Mounting Medium Kit
Technovit 3040 yellow is a fast curing methyl methacrylate-based resin, whose chemical composition warrants a firm, durable bond between Technovit and the specimen.
Technovit 3040 consists of two components–powder and liquid–allowing simple mixing, easy adherance to the specimen, and fast curing. For fixing the mount, a high viscous consistency is required(i.e. a mixing ratio of approximately 2-3 parts per volume powder: 1 part per volume liquid) has proven to be the most advantageous.
ABBERIOR INSTRUMENTS AMERICA LLC MOUNT SOLID ANTIFADE
abberior MOUNT SOLID ANTIFADE is an aqueous mounting medium designed for confocal and superresolution microscopy. The refractive index (before hardening) is identical to that of many biological samples (n=1.38). Specimen mounting using abberior MOUNT SOLID ANTIFADE is convenient since no dilution series is required. After specimen mounting, the embedding medium is hardening. So sealing of the mounted specimen with nail polish or similar is not required. abberior MOUNT SOLID ANTIFADE prevents photobleaching and preserves the signal of fluorescent labels. For scientific use only. Must not be used for diagnostic or medical purposes.
Electron Microscopy Sciences CytoSeal™ Mounting Medium 60 Mounting Medium 16 OZ
CytoSeal 60 and 280 are toluene-based mounting mediumformulated from acrylic resins that will not crack or discolor with age. An antioxidant has been added to the formulation to inhibit fading or yellowing of stained specimens. It will not become brittle and crack, nor will it discolor or yellow with age. CytoSeal can be dissolved in toluene or xylene. Low-viscosity medium dries quickly and spreads evenly and rapidily virtually eliminating air bubbles.
Andwin Scientific TISSUETEK VIP MEDIA/8X1KG/1CS
The Tissue-Tek V.I.P. permits superior sample preparation and less compression in sections as thin as 2. This product is ideal for processing and embedding. It does not leave plasticizer residue to clog paraffin lines and will not discolor or produce resin precipitate. It is sold in the quantity of 1 kilogram.
Abcam Limonene Mounting Medium, 30ML
Limonene Mounting Medium ab104141 is an organic mounting medium compatible with chromogens such as DAB.
The product is subject to the following: Abcam Restricted Use Statement
![Buehler EpoxiCure 2 Resin, 64oz [1.9L]](https://assets.fishersci.com/TFS-Assets/CCG/product-images/OS-0011459EPOXICURE-2-RESIN-64OZ19L.JPEG-250.jpg)
Buehler EpoxiCure 2 Resin, 64oz [1.9L]
This item has a minimum qty of 2 per supplier requirements.
EpoxiCure 2 is a clear general purpose epoxy system with a 6 hr cure time. 64 oz
Electron Microscopy Sciences Citifluor™ Mountant Solution AF87, Glycerol Free, Non Hardening 25 ML
Citifluor mounting medium for immunofluorescence is designed to reduce the fading of the fluorescence of dyes used for labeling biological specimens. In the technique of fluorescence microscopy, the fluorescence is stimulated by high intensity UV and/or visible light. Absorption of the light populates an excited state of the dye (usually a singlet state) and this leads to fluorescence. However, the excited state of the dye may undergo chemical reaction, which leads to destruction as evidenced by the fading of the fluorescence and consequent loss of the image. Immersion oil having a refractive index of 1.52 and contains an antifadent.
Material: Glycerol Free
Type: Non Hardening